Walk Way Cantilever Canopy

 

cpaconcept1

We can manufacture the above car port to produce a 940mm walk way canopy use with a gutter pack for a complete kit 

More Information

Cantilever walk way canopies are designed on a modular basis which means that you can increase the area of the cover at any time and there are no support pillars needed.
Your canopy will keep its good looks for years and years without continual upkeep. All you need to maintain the elegant looks is an occasional wipe clean. The tough translucent roof panels allow natural daylight through, so if your canopy is above your kitchen window, patio or living room, adequate daylight still enters your home. Adds value to your property.
Cantilever Canopy requires no ground preparation and in most cases planning permission is not necessary(Call your local planning authority to check.) ALL MATERIALS ARE GUARANTEED FOR FIVE YEARS. 

Cantilever Walk Way Canopies are sold in a standard .

Delivery times vary according to season this product is manufactured to order allow 7 - 21 days for delivery

!

940mm x 1675mm
W/2/940
!
Cantilever Canopy
This Cantilever Canopy uses two beams. Supplied with 1 left hand and 1 right hand beam

Enter width required in millimetres i.e max = 940mm

Gutter Pack 940mm x 1675mm

CPGP1S
!
940mm x 1675mm Fascia And Gutter Pack

 

Gutter designed to run across the front of the roof along one side ending with a stop end outlet against the wall  

940mm x 3275mm
W/3/940
!
Cantilever Canopy

This Cantilever Canopy uses three beams.

Enter width required in millimetres i.e max = 940mm

The beams with this roof system are finished on one side please select your requirements from the drop down box the picture at the top of the page shows a left hand beam the picture on the bottom of the page shows a right hand beam.

Gutter Pack 940mm x 3275mm

CPGP2S
!
940mm x 3275mm Fascia And Gutter Pack

 

Gutter designed to run across the front of the roof along one side ending with a stop end outlet against the wall  

940mm x 4875mm
W/4/940
!
Cantilever Canopy

This Cantilever Canopy uses four beams.

Supplied with 2 left hand and 2 right hand beams

Enter width required in millimetres i.e max = 940mm

Gutter Pack 940mm x 4875mm

CPGP3S
!
940mm x 4875mm Fascia And Gutter Pack

 

Gutter designed to run across the front of the roof along one side ending with a stop end outlet against the wall  

940mm x 6475mm
W/5/940
!
Cantilever Canopy

This Cantilever Canopy uses five beams.

Enter width required in millimetres i.e max = 940mm

The beams with this roof system are finished on one side please select your requirements from the drop down box the picture at the top of the page shows aleft hand beam the picture on the bottom of the page shows a right hand beam.

 

Gutter Pack 940mm x 6475mm

CPGP4S
!
940mm x 6475mm Fascia And Gutter Pack

 

Gutter designed to run across the front of the roof along one side ending with a stop end outlet against the wall  

940mm x 8075mm
W/6/940
!
Cantilever Canopy
This Cantilever Canopy uses six beams.

Supplied with 3 left hand and 3 right hand beams

Enter width required in millimetres i.e max = 940mm

Gutter Pack 940mm x 8075mm

CPGP5S
!
940mm x 8075mm Fascia And Gutter Pack

 

Gutter designed to run across the front of the roof along one side ending with a stop end outlet against the wall  

940mm x 9675mm

W/7/940
!
Cantilever Canopy
This Cantilever Canopy uses seven beams.

Enter width required in millimetres i.e max = 940mm

The beams with this roof system are finished on one side please select your requirements from the drop down box the picture at the top of the page shows aleft hand beam the picture on the bottom of the page shows a right hand beam.

Gutter Pack 940mm x 9675mm

CPGP6S
!
940mm x 9675mm Fascia And Gutter Pack

 

Gutter designed to run across the front of the roof along one side ending with a stop end outlet against the wall  

940mm x 11275mm
W/8/940
!
Cantilever Canopy
This Cantilever Canopy uses eight beams.

Supplied with 4 left hand and 4 right hand beams

Enter width required in millimetres i.e max = 940mm

 

Gutter Pack 940mm x 11275mm

CPGP7S
!
940mm x 11275mm Fascia And Gutter Pack

 

Gutter designed to run across the front of the roof along one side ending with a stop end outlet against the wall  

940mm x 12875mm
W/9/940
!
Cantilever Canopy
This Cantilever Canopy uses eight beams.

Supplied with 4 left hand and 4 right hand beams

Enter width required in millimetres i.e max = 940mm

 

Installers
!

Need a local approved cantilever carport installer click here to email please supply your name full postal address and a contact telephone number. We will then pass your details to our nearest approved installer.

!

Telephone Orders

We are happy to take your order or enquiry by phone

Please call us on 0117 971 9922

We are open 8am - 5pm Monday to Friday & Saturdays 8am - 12pm

© Copyright 1994-2007, Master Plastics (SW0 Ltd Bristol | Clevedon. All rights reserved world-wide.

Many of the images on this site do not belong to us. Do not copy or link directly to them. Contact us so we can seek permission where necessary on your behalf.

WE DELIVER UK NATIONWIDE ENGLAND SCOTLAND WALES AND IRELAND..